With the numbered paragraphs shown above, there is no extra spacing between the paragraphs. That’s easy to fix. Go ahead and type out at least part of your first numbered paragraph, then go to the Page Layout tab and adjust the value of Spacing After in the Paragraph section. Still no extra space? There’s one more setting to check. Click the launcher arrow in the lower right-hand corner to go to the Paragraph dialog box, uncheck the box next to “Don’t add space between paragraphs of the same style.” Click OK. That paragraph and all the remaining numbered ones will have more breathing room.
There are a couple of ways you can set up Word 2007/2010 to use SEQ fields for numbering — you can set them up as AutoCorrect entries or as Quick Parts. Both ways work; the method you choose is up to you. This long article describes how to create the SEQ fields and the numbering style in your Normal.dotm template; how to save the SEQ fields as AutoCorrect entries in Word 2007/2010 (and how to use them); and how to save (and use) them as Quick Parts. The most consuming part of this process is settings up the fields and the style; once they’re set up, using them is super easy.
OK, First, you need to reread the blog. You should NOT be storing the Transaction_ID. It is a calculated value. Second, your naming is what confused me. Your Passenger table should have an autonumber PassengerID. That PassengerID should be the Foreign Key in your Reservations table. Your servation table should also have an autonumber for ReservationID. I really don’t see why you need sequential numbering in the passenger table. I can understand it in the Reservations table, but not in the passenger table. Also, I don’t see any reason for a transaction date in the passenger table. I can understand a CreateDate for when the passenger signed up.
For whatever reason, AllExperts did not let me post a direct reply to your response re: “Ok, what is the ControlSource of the Fixture Number control? It should be: =cboZone & “-” & Format(Me.FNumber,”000″)” and adding “Me.Refresh” to my code (within the last 10 minutes). It just had the “rate this reply”. I added the Me.Refresh and corrected my location of the =cboZone code and it works correctly now.
Is there a way to code the special interrogatory numbers wherein the identify of documents is requested such that those specific special interrogatories (and only those specific special interrogatories) are automatically generated in a separate demand for production of documents? In other words if Special Interrogatory numbers 3, 6, 9, 12 request identification of documents, is there a way to code those special interrogatories so that within the demand for production of documents, those specific but individual special interrogatory numbers can be referenced?
I'm producing gift certificates for a restaurant and they need to be numbered sequentially from 0001 to 0250. Is there any way to do this easily as opposed to numbering each manually? I'm sure I could probably work it out with a print shop, but the job was thrust on me last minute and my options are limited by the short turn around time. Any help would be appreciated. Thanks!...
Thanks for the head start on this, it got me part the way through my problem but I found that when I had 3 figures in a row then a map, the next figure would jump back to #.1 again. Because I had figures, maps and tables that needed to be numbered I used the ‘levels’ to differentiate between them as you suggested, but found if you create a new number list for each entry ie. number list for maps, and number list for tables etc then they don’t conflict. thanks for the start off though. no where else pointed it out as clearly as this. Cheers
Angie, have tried your method; however, I encountered what I surmised was a limit on the amount of characters allowed in that “Enter formatting for number” box: for instance, I can only type as far as “Request for Productio” (excluding quotations)- additional text and codes delete and default back to the incomplete phrase “Request for Productio”. Seems to have a default of 26 characters – anything exceeding that is deleted. The phrase “Request for Admission” completes, but am unable to include anything after that phrase of 26 characters. Not sure why that is, but that’s what I run into when I attempt using the multi-list option.
Now, what’s the deal with the UniqueKeyVariant parameter for the RowNumber() function? We are not even using it all! True, but if we didn’t, Access will call RowNumber() only once for an entire query and thus we get “1” for the entire dataset. That is a good way to save on CPU processing – why call Now() for each row? In this case, we want to go against this CPU-saving measure and ensure that the RowNumber() is in fact called once per row to generate a new number for that row. Thus, we pass in a parameter — a primary key of a table is a good choice for this purpose. So we get a nice sequential number generated all in the query with VBA function.
WordTips is your source for cost-effective Microsoft Word training. (Microsoft Word is the most popular word processing software in the world.) This tip (92) applies to Microsoft Word 97, 2000, 2002, and 2003. You can find a version of this tip for the ribbon interface of Word (Word 2007 and later) here: Sequentially Numbering Elements in Your Document.